Jay Fisher - Fine Custom Knives

"Ari B'Lilah" Professional Grade Counterterrorism Combat Knife (Shadow Line)
All Matching in non-reflective flat black camouflage

• Size: Length overall: 12.25" (31.1 cm), Blade Length: 6.0" (15.2 cm), Thickness: .231" (5.9 mm)
• Weight: Knife: 16 oz. (454 grams), Leather Sheath: 8.5 oz. (241 grams), Hybrid Tension-Locking Kydex Sheath: 12.1 oz. (343 grams)
• Blade: ATS-34 High Molybdenum Martensitic Stainless Tool Steel, Hardened and Tempered, T3 Specialty Cryogenically treated to Rockwell C60.5, proprietary surface oxide treatment "Ghost Slate."
• Bolsters/Fittings: 304 High Nickel, High Chromium Austenitic Stainless Steel, proprietary surface oxide treatment "Ghost Slate."
• Handle: Black G10 Fiberglass/Epoxy Composite
• Sheath: Heavy 9-10 oz. thick leather shoulder, hand-stamped, black lacquered
• Sheath: Hybrid Tension-Locking in Black Kydex, Black Anodized Aluminum Alloy, Blackened Stainless Steel, 6AL4V Titanium
• Accessories:
  • Standard Belt Loops: accommodates .190" thick by 1.5" belt, black anodized 5052H32 high strength corrosion resistant aluminum alloy, anodized black at 1 mil thickness
  • High Profile Belt Loops: accommodates .250" thick by 1.5" belt, black anodized 5052H32 high strength corrosion resistant aluminum alloy, anodized black at 1 mil thickness
  • Vertical Flat Mounting Straps: accommodates up to 2.4" wide belt, web, strapping, or gear, clamps rigidly and vertically 90 degrees to the long axis of the sheath, black anodized 5052H32 high strength corrosion resistant aluminum alloy, anodized black at 1 mil thickness
  • Horizontal Flat Mounting Straps: accommodates 1" to 3" wide belt, web, strapping, or gear, clamps rigidly and horizontally (in line with the long axis of the sheath), black anodized 5052H32 high strength corrosion resistant aluminum alloy, anodized black at 1 mil thickness
  • Horizontal Belt Loop Plates: allows wear with the long axis of the sheath in line with standard belt, without rigid clamping, accommodates .250" thick by 1.5" belt, welded black anodized 5052H32 high strength corrosion resistant aluminum alloy, anodized black at 1 mil thickness
  • Vertical High Strength Flat Mounting Straps: allows rigid and high strength clamping of sheath to web, strap, or both belt loop extenders, made of drilled and milled blackened 304 high nickel, high chromium stainless steel
  • Ultimate Belt Loop Extender (UBLX): allows wearing with locking sheath and knife handle just below the belt line, with DMT folding pocket diamond abrasive sharpener, in black polypropylene, polyester, black acetyl buckles. DMT diamond sharpener. More about the UBLX on this dedicated page.
  • Extended Length Belt Loop Extender (EXBLX): allows wearing with locking sheath and knife sheath below the belt line, sheath tail just above knee, with 2" wide leg strap, in black polypropylene, polyester, blackened stainless steel, acetyl buckles. More about the EXBLX on this dedicated page.
  • HULA with Fenix E35UE 900 lumen flashlight: provides a primary, fully adjustable flashlight in removable holder, with a frame that can be aimed and locked in any direction, mounted on the sheath body no matter where the knife is worn. This is the very best, most durable flashlight holder made in the world today. More below.
  • Sternum Harness Plus: allows wearing of locking sheath upside down across sternum, handle down, in black polypropylene, polyester, acetyl buckles
  • Lamp Independent Mount Assembly (LIMA): Backup, emergency, safety LED programmable flashlight and independent web frame and mount, in polypropylene stitched with high strength polyester, anodized 5052 high strength corrosion resistant black anodized aluminum mounting bar, 304 stainless steel ring retainers, nylon elastic shock cord, with ThruNite Ti3 flashlight. More about the LIMA on this dedicated page.
  • Diamond Abrasive Sharpener with Pad/Sheath: Diamond abrasive sharpening stone, 2" x 6", double-sided (400G/600G), nickel bonded diamond abrasives over phenolic core, heavy nylon sheath to store and protect other gear from diamond abrasives; sheath doubles as work pad so diamond does not scratch surfaces, stitched with polyester, hook and loop closure
  • Lanyards: 550 Nylon Kernmantle Rope (Paracord) sliding noose lanyard, waterproof adjustable SCUBA lanyard with silicone rubber padding
  • Hardware and Fasteners: all in 8-32 standard thread, 304 (18-8) high nickel, high chromium stainless steel, blackened, all user-changeable with one size of hex wrench. This differs from my kits of the past, where two or three sizes of hex wrenches are needed. I've tuned up the fastener set so that, in this particular style of knife sheath, only one hex wrench (Allen wrench) is needed for all of the fasteners: 3/32". A smaller hex wrench (5/64") is needed to reverse the locking components of the hybrid tension-locking sheath. Also necessary is a simple flat bladed screwdriver (not included) to make up all of the typical hardware arrangements.
  • Duffle Bag: 1000 denier Cordura® ballistic nylon, waterproof polyurethane coated, nylon, polyester, polypropylene sling handles, closed cell foam bottom in 600 denier Cordura nylon bag for storage of papers, thin gear, protection from abrasion, embroidered patch, removable embroidered name patch with hook and loop
• Knife: This is my most popular professional counterterrorism and tactical combat knife for a reason. It's designed with and made for real counterterrorism professionals and is one of the most sought after knives on the planet. "Ari" is the Hebrew word for lion, and the lion is the sign of the tribe of Judah and Jerusalem and is even called the Lion of God. Made for daylight and more importantly critical night operations, this knife is the Ari B'Lilah (lion by night), and is one of the most sophisticated and unique counterterrorism knives in the world. Unlike most knives, this knife was created with the direct input of professionals of a top Israeli YAMAM counterterrorism unit, widely recognized as the most elite and effective counterterrorism unit in the world. This is a knife designed for the most serious of action. It's a great honor to have the input, guidance, and direction of these professionals, who requested a series of extremely efficient, well-designed and constructed, lethal combat knives with some special features, built to the highest standards possible: what I'm known for in tactical combat knives, sheaths, and accessories.
  • Blade Steel Alloy: The Ari B'Lilah blade is a special hypereutectoid, high alloy stainless tool steel, ATS-34. This steel is extremely high in molybdenum and chromium, and I call it a "chrome-moly tool steel on steroids." First, the carbon in this steel is extremely high at 1.25 percent, allowing significant development of martensite and forming of essential iron carbides. The second element is chromium, and at 14 percent, this is a true stainless steel with high corrosion resistance. High chromium also helps create extremely hard and durable chromium carbides adding to the wear resistance and overall strength and stability of the steel alloy. The third and most transformational element is molybdenum. ATS-34 has 4% molybdenum, providing a high concentration of molybdenum carbide particles, which are extremely wear-resistant and contribute tremendously to toughness. Molybdenum is a very important carbide-former, and it helps precipitate carbides at critical dislocation and grain boundary areas of the crystalline structure, stabilizing the structure against fracture, toughening it. Toughness is resistance to breakage, and since this is dramatically increased in this high molybdenum steel, it allows a very thin cutting edge and blade geometry with high strength. This means a thinner, sharper, and extremely tough, corrosion-resistant blade is possible with this steel.
  • Heat Treatment: This Ari B'Lilah has my T3 heat treatment, yielding an astounding blade in incredible condition through advanced processing protocols. How advanced is this treatment? It's a multi-stage cryogenic treatment, involving temperatures ranging in over 2000°F (1090°C) to -320°F (-196°C). The process is an evolution of my advanced heat treating processes, and consists of 33 dedicated and specific steps and takes 172 hours! This means that just to heat treat this blade takes over a week! The reason for this is scientific and critical, but yields the most stable, most wear-resistant, most durable and long-lived structure of this steel, profuse with fine multi-element carbides and a uniform and unbelievably robust structure. This is a testament to my determination to make the very best knives, steels, treatments and kits in the modern world. I know of no one else who has advanced the treatment to this level; it's unheard of in the metals and knifemaking field.
  • Blade Design and Geometry: The blade of the Ari B'Lilah is double-edged and hollow ground; the main cutting edge is hollow ground with a 3" diameter wheel and the top edge with serrations is hollow ground with a 3" diameter wheel. This is an extremely difficult grind profile, and the purpose is to create two complimentary edges, both yielding extremely thin and razor-keen edges with a high longevity while preserving a good cross-sectional thickness of center spine to support thrusting and the point. The point of this knife is critically strong; it is ground in a very ancient design called "armor piercing." This is not for piercing today's armor, but for piercing chain mail of old: interlocking metal rings woven into a tough mesh. This is the strongest possible point that will still offer extremely sharp and lethal penetrating potential, resisting any tough or hard materials such a thrust could encounter without breaking. The point is carefully hand-ground at the maximum edge angle (25 degrees) possible that can still provide a keen and slicing single-bevel cutting edge. The geometry of the point is a solid "diamond" (in cross section), as tough and lethal as a knife point can possibly be. The point is created by an interrupted hollow grind; the transition to strong point is well-matched and supported by the full thickness spine running down the center of the blade. Both cutting edges are single bevel. This means that there is one slanted line (bevel) from the hollow grind that creates the cutting edge. Most knives are made with double bevel edges, increasing the actual cutting edge angle. The main non-serrated cutting edge is is a straight tanto which has 2.5" of piercing point in front of the dividing line (yokote), and 3.4" of straight edge between the dividing line and the choil. The top edge is designed with my Hammerhead serrations, which are extremely tough and aggressive, with reduced snagging and wide transitions between concavities and segmented edges. This is my most requested serration profile because it is extremely aggressive and tough. The grinds on the blade are accurate, concise, and with nicely radiused grind terminations for great transfer of energy without stressing the blade-to-handle ricasso area while a very long supportive spine runs the length of the blade.
  • This is an extreme use, high wear resistance, highly tough, and extremely keen high alloy stainless steel blade with advanced heat treatment.
  • Blade Finish: The blade and bolsters (and all of the accessories) are in my "Shadow" line of counterterrorism and tactical knife finishes. Answering the request for completely subdued and non-reflective surfaces, I developed the Shadow Line with my Ghost Slate finish. This means darkening in a permanent fashion not only the stainless steel of the knife, blade, handle, and fittings, but all of the gear in the entire kit: the fasteners, the sheath parts, aluminum mounts, accessories and entire package. Read more about my Shadow Line and Ghost Slate finish on my Counterterrorism Knives page at this bookmark.
  • Bolsters: I bolstered the Ari B'Lilah with my signature zero-care, high nickel, high chromium 304 austenitic stainless steel bolsters, contoured and rounded for comfort of the hands, and shaped and radiused in the front face for easy cleaning. They are attached with multiple through-tang pins of 304 stainless steel, and the mounting is permanent, as well as extremely corrosion-resistant. This is the same steel used for stainless steel nuts, bolts, and fasteners, and the bolsters are heavy, thick, and solid, giving great balance to the knife. The front bolster is contoured around a 1.11" (2.82 cm) diameter forward finger ring, which is rounded and radiused for comfort and smoothness. The finger ring offers maximum security between the hand and the knife, essential in the most critical of counter-terrorism and combat tactical offensives. This is a feature that is key in cementing the hand-to-knife grip. The forefinger and thumb grip between the thumb rise and the finger ring, and this reinforced area is key to the control of the knife. The ring and thumb rise allow tremendous force to be applied to the blade where it is needed. The rear bolster has a large chamfered 3/8" (10 mm) through-tang lanyard hole for added security when working elevated or over water or in a debris field. The bolsters are dovetailed to create a solid, seamless union with the handle material. The bolsters are treated in my "Ghost Slate" shadow line for reduced glare and match the rest of the knife and gear.
  • Handle: The handle scales are black G10, a fiberglass reinforced epoxy composite that is one of the most durable and dependable manmade handle materials on earth. The handle scales are dovetailed and locked and bedded under the bolsters, secured with two heavy 304 stainless steel pins. The handle shape is comfortable and extremely secure, with deep quillons, good belly, and slope for the heel of the hand that makes the knife an extension of the arm. The tang is fully fileworked with an bold and well-defined arrow pattern for increased purchase and handmade signature. The tang is fully tapered, with plenty of thickness at the butt for a substantial stout talon (skull crusher or persuader) also applicable for non-lethal inducement. Additional uses for this feature include glass breakage, breaching, and hammer-clawing for material destruction for entrance. The heavy rear bolster is significantly mounted to the tang, and has an extra-large 3/8" through-tang lanyard hole for super security when working elevated or near water or in special circumstances that require insurance against dropping the knife. The large lanyard hole is chamfered and dressed smooth for abrasion reduction of the lanyard and is easy and fast to thread.
  • Balance and Feel: The center of balance of the knife is exactly between the first two fingers. The knife feels extremely solid and durable in forward grip, blade leading. In reverse grip, with the small finger threaded through the ring and the thumb over the heel with the tip at the talon, the knife feels robust and tough. The unique handle shape, balance, thickness, and stout design of this knife makes it an incredible tool and weapon. This is, clearly, the very best counterterrorism knife made in the world today.
• Leather Sheath: I've included a heavy, tough, and solid leather sheath for the Ari B'Lilah, in 9-10 oz. leather shoulder, hand-stamped and tooled. The leather is shoulder, from mature cows, and is twice as thick as most other knifemakers use. The stamp-tooling is a tri-basketweave pattern for visual interest and breaking up the light and reflection. It's also useful for traditional and conventional wear options. The sheath has a belt loop that is double-stitched throughout with the toughest nylon thread that is water and sunlight resistant. The knife fits deep and secure into the sheath, with the handle exposed and the high back of the sheath protecting the wearer. The entire sheath assembly is double-row stitched for extreme durability. The sheath edges are dressed and smoothed for comfort; the entire sheath is sealed with lacquer for water resistance, permanence, and longevity. Leather is irreplaceable in extremely cold or hot environments, and where absolute silence is needed in tactical operations with no clicking when in contact against objects, people, or gear. The leather sheath is also great for a "non-tactical" outdoors look in a more casual setting when a knife simply needs to be a tool.
• Hybrid-Tension Locking Sheath: This sheath is one of my hybrid tension-locking models, originally made for my skeletonized knives, but specially adapted to this fully bolstered and handled knife. This is a proprietary design, the best possible sheath of its type available in the world today. Actually, it is the ONLY type of this sheath available in the world today! The sheath is built of double thickness (.125" thick) kydex (methyl acrylate and polyvinyl chloride) over a welt-frame of black anodized 5052H32 corrosion resistant high strength aluminum alloy. I've meticulously anodized all of the aluminum surfaces, even through holes, of each welt component, mount, fitting, and fixture for extremely high durability, ultimate corrosion resistance, strength enhancement, and muted appearance. If you're not familiar with anodization, it's a chemo-electric process that creates a near-ceramic hard surface on the aluminum alloy, a surface that increases wear resistance tremendously, and a surface that can accept permanent dyes that are sealed in place. For my black kydex sheaths, the anodized aluminum color is black for low reflectivity and matching appearance. For high durability, the anodized surface is a full 1 mil thick. The sheath is bonded with waterproof cement and bolted together with all blackened 304 stainless steel Chicago screws for zero care and extreme corrosion resistance while being dark and non-reflective. The tension-lock sheath comes with plenty of hardware for mounting and wearing; see the details below. On this particular knife, the belt loops have 10 different locations with multiple combinations for versatile wear. All of the mounting assemblies are reversible, as is the spring retention for the tension-lock sheath, so the versatility of this sheath is unsurpassed. It's also completely and absolutely waterproof, for zero worry about exposure. The knife can be unsheathed by finger pressure against the spring tab, or by a hard pull in an emergency. Included are three different titanium springs, so my client can choose the tension he desires, light, medium, or heavy, depending on the gear he mounts it to, the angle and orientation, and his personal preference for a pull-to-release tension. What a versatile package!
• Sternum Harness Plus: The sternum harness I've included is the result of input from my military and counterterrorism clients. It allows the knife to be worn, handle down, angled across the sternum, on top of any other tactical gear. This harness is made of polypropylene and stitched with polyester for rot-free, high strength longevity, and the buckles and straps are tough Acetyl plastic with 110 lbs. breaking strength. The harness can be donned and doffed quickly and simply, and the "plus" is the additional one-inch wide stabilizing strap and buckle that creates an "X" strap around the torso, to prevent movement in any position of the wearer, even while running and climbing. I've even included several snap hooks for extra gear, and these can be removed or placed at different points on the harness.
• Ultimate Belt Loop Extender (UBLX): I included my ultimate survival, CSAR tactical, rescue, and counterterrorism sheath belt loop extension with outstanding and critical features and devices. The nylon and polyester accessory is waterproof, durable, and extremely stout, and lowers the hybrid tension-locking knife sheath to be worn in a more traditional belt position with the knife handle below the hip. The extension is mounted with 304 stainless steel straps and stainless steel cap screws attached to the existing stainless Chicago screws, and the assembly is stiffened by trapped acrylic stiffeners stitched in place with polyester. These prevent the extension from folding, bending, or collapsing when the knife is extracted from the sheath. The belt loop is 2 inches wide for standard tactical belts, and has a mid-placement 1" wide strap retained with acetyl buckles to prevent the knife handle from flopping around during active movements (running, climbing, crawling). At the lower back of the extension I've included a custom fit pocket for a DMT (Diamond Machining Technology) Mini-Sharp diamond-nickel abrasive hone, to bring up the cutting edge in the field with ease, and it works even on this high alloy  wear-resistant blade. These are great tools that can re-sharpen or just touch up even the hardest tool steel edges, as they are surface-bonded with diamond abrasives. The pocket for this tool is situated at the sheath back and against the body, so the sharpener can not be removed unless the sheath is off the body and the industrial strength Velcro (hook and loop) closure is open. Read more about the UBLX at this link.
• Extra Length Belt Loop Extender (EXBLX): Responding to requests, I've included an extended length belt loop extender in this kit. This works the same as the UBLX above, but it's even longer and has a 2" wide acetyl-buckle leg strap to secure the knife on the side of the thigh, just above the knee. The wide strap is very comfortable, over pants; it's adjustable yet can be quickly removed in an emergency with the squeeze-type acetyl buckle. This frees up critical space if the user is wearing body armor, load belt, or does not have room for the knife in the traditional location. Marines who wear and use my knives in combat have requested this critical assembly, since on the leg is the only real estate they have available! The neat thing is the HULA attached to the sheath with the EXBLX on the leg allows a blinding flood of light for breaching and entrance into enemy-infested buildings with maximum illumination and the associated disorientation necessary to quickly reach a tactical advantage and solution. Read much more about this critical accessory at this link.
• LIMA Emergency Lamp (Lamp Independent Mount Assembly): An important lesson I learned from my military and counterterrorism clients is the addition of the emergency lamp. The LIMA is a special socket in thick and wide polypropylene, stitched with polyester for durability and rot resistance, and it accommodates the latest small lamp, the LED ThruNite Ti3. This little, super-lightweight flashlight puts out an incredible 120 lumens and at lower levels can last for 115 hours on lowest setting. It can reach out 164 feet and give you enough light to get to safety, and the entire mounting assembly is extremely lightweight and waterproof to continual immersion. The flashlight even has an emergency strobe at high illumination that will get noticed. The LIMA webframe is secured with a lightweight anodized aluminum strap and stainless steel machine screws and mounts anywhere along the sheath welts where I have the standard 2.5" spacing. The retaining strap rings are also 304 stainless, and the 1/8" shock cord is easily replaceable if needed, and replacement shock cord is included. More about the LIMA on this dedicated page.
• HULA (Holder, Universal, Lamp, Articulating) with a Fenix E35UE. (Please note that a variety of flashlight types can be included with the HULA) Included in this professional assembly is my HULA, the "Holder, Universal, Lamp, Articulating" (HULA), and my answer to a call for not just a backup lamp, but an actual primary or "key" professional grade tactical lamp and mount assembly. The lamp I included with this kit is the Fenix E35 "Ultimate Edition" which is one of the brightest most sophisticated flashlights available today. It puts out an amazing 900 lumen burst, with three brightness levels, and can run on a rechargeable lithium battery or two CR123 batteries commonly found in battlefield gear like night vision goggles. The only thing the flashlight needs is a reliable, adjustable, dependable and corrosion-proof way to mount, use, and carry it on the sheath, so I designed the HULA. This special holder is designed for the Fenix E35UE; the lamp frame holder is made of welded 5052H32 high strength corrosion-resistant aluminum alloy, for the highest durability and corrosion resistance combined with low weight This aluminum is suitable for marine (salt water) environments, and to add to the already superior material, I've completely anodized the aluminum with a 1 mil thick surface, dyed permanently black. This is a near-ceramic hard surface that improves wear resistance, corrosion resistance, and adds tremendously to the longevity and durability of the metal. This same process is used in the flashlight's aluminum body. The light is held in custom-fitted socket with a retaining cap that is held in a T-slot lock by the elastic tension of replaceable shock cord straps. The T-slot lock can be negotiated even in the dark due to it's simple and clever design and construction. The lamp can be turned on and operated within the holder, and can even change selected modes while still in the retention of the holder. One of the best features of this assembly is my exclusive ball joint and pinch mechanism. This is a very old mechanism, dating back to 200BC, where a ball sits in a dedicated socket, and is held there by the tension of a pinch screw. The ball joint frame, ball, tangs, screw and mounting hardware are all welded 304 high nickel, high chromium stainless steel which is media-blasted and darkened with a permanent oxide finish for glare reduction. This is a very tough assembly that will probably outlast the knife owner. What it offers is an articulating adjustment, aiming and positioning of the lamp, while still mounted on the knife sheath, wherever the knife sheath is mounted on the body. In the traditional belt line position, the lamp can be aimed at the ground in front of the wearer (great for hiking or movement), or aimed at any object or person in front of the wearer, while freeing the hands for a weapon, tool, or carry. Having the HULA also eliminates the need for a headlamp, a device that has its own limitations (detailed at the link below). This HULA development has been highly popular with search and rescue and disaster response teams, as well as my counterterrorism knife users. If the wearer needs the light in his hand, he simply pulls up on the T-slot locking cap, pulls the lamp from the socket, and replaces the cap so it won't bounce around. I've done my research, and created simply the finest and simplest flashlight accessory made in the world today, custom made to mount to my locking sheaths, the best locking sheaths made in the world today. One more important point: the bolt pattern and arrangement on this particular knife sheath allows the HULA to be bolted to 10 positions and 20 orientations along the welts of the sheath. Talk about flexibility! There are much more to these accessories; learn about these critical accessories on a special page on my site at this link. Mounting, care, and use instructions are posted there.
• Horizontal Belt Loop Plates: Answering the call of my counterterrorism and military clients, I've included a pair of horizontal belt loop plates for this knife sheath. These bolt onto either side of the sheath using included hardware, and are 5052H32 high strength corrosion resistant aluminum alloy, completely anodized and permanently dyed black with a near-ceramic hard surface. They are high-purity welded for durability, and light weight. They allow horizontal wear of any belt up to 1.5" wide, and the sheath runs inline with the belt.
• Flat strap plates (horizontal and/or vertical): These have several uses: one is to mount the knife sheath rigidly clamped to the sternum harness, with no play. They also allow the sheath to be clamped on any gear (like PALS webbing) with a solid strap security and no sliding around (like on traditional belt loops). So they clamp the sheath to your gear with all stainless steel hardware. They accommodate any web strap up to over 2" wide. They are also 5052 H32 high strength, corrosion-resistant aluminum alloy, anodized with a permanent black color, and a near-ceramic hard surface.
• High and Low-profile belt loops (footman's loops): I've included two pairs of anodized aluminum belt loops, one pair that accommodates 1.5" wide belts up to .250" thick and one pair that accommodates 1.5" wide belts up to .190" thick. They work with the integrated spacing so can be mounted in a variety of positions on the reversible sheath.
• Lanyards, hardware, tools: The included paracord (550 Nylon Kernmantle Rope) sliding noose lanyard can be critical and necessary for retention of your knife when working in elevated locations or in marine environments. It's an adjustable type, a frequent request by my tactical combat professionals. I've also included a SCUBA-rated waterproof lanyard with silicone rubber abrasion-resistant sleeve and locking cord adjuster for adjustment. I've included all the tools, hardware, and necessary components to mount all or any combination of these accessories with your gear, on your person, and all of the hardware is blackened, non-reflective stainless steel in common American Standard Sizes. Included is screw top and snap tins for hardware storage. Also included is an archival engraved acrylic tag detailing the components with my contact information. Detailed Instructions and care information for the individual components are also included, and they nest well at the bottom of the duffle bag (below) in the padded sleeve. I've also included a list of video links that explain how to set up every single one of these accessories. This is an ultimate system, and demonstrates my commitment to actual combat, tactical, field, rescue, and counterterrorism knife service in my trade.
• Leather Sheath Storage: I've included my black denim embroidered drawstring bag with this kit (see photos below). This is to store the leather sheath; it breathes and keeps the sheath from being scuffed or abraded, and I make these in heavy denim, stitched with polyester, I embroider one side with "Jay Fisher Knives" and the other with my maker's mark. The drawstring is polyethylene and it keeps the sheath protected and clean even while in the duffle (below).
• 2" x 6" dual diamond sharpener and storage/pad: This is a new accessory, and one that I'll be including in all my newer kits. It's a double-sided diamond sharpener, with two grits, 400 and 600. Diamond is the only abrasive I recommend for sharpening, and it's important to have it available and included. Because diamond is the hardest known substance, it makes an excellent abrasive for the very hardest, toughest and most wear-resistant cryogenically-treated tool steels. Because diamond is so hard, special care must be taken in handling and storing the sharpener, as it absolutely will scratch every single surface it comes in contact with! This is why I've gone to the extra effort to create an incredible, tough, and durable pad/bag for it. The diamond pad is stored easily in the heavily-stitched thick nylon bag, and secured with industrial strength hook and loop. When the diamond pad is out of the bag, the owner can set it on top of the bag, using it as a thick, heavy, protective flat pad for sharpening his knives. He can even use it as an assembly pad for laying his knife on for adjusting, servicing, or cleaning. This is the heaviest, thickest piece of nylon you will find! A great addition to the kit!
• Heavy 7" x 11" Duffle: It's important to keep everything together, safe, and accessible, and since no on makes a duffle heavy and stout enough for the job, I make these, too. I make them in 1000 Denier Cordura® ballistic nylon, coated on the inside with polyurethane for water resistance. This is some of the heaviest, toughest material available, and I've double-row stitched all of the seams with strong, waterproof, sunlight-resistant heavy polyester thread. I've attached stout metal #8 zippers and double pulls, and reinforced the zipper ends as well as the 2" wide polyethylene carry straps. I've even included a 7mm thick closed-cell foam inner base pad, wrapped in 600 Denier Cordura nylon in the bottom to prevent abrasion and wear. You can store paperwork, written or printed orders, and other items in the base bag to keep them flat and clean. The duffle is identified with my "Quality Without Compromise" patch. Because many of my clients have more than one knife, I've also include an embroidered knife name patch, which is removable and secured by hook and loop so knife owner can tell which duffle stores which knife. See photos below.
• Archival engraved detail plate: As with all of my knives, I've included a co-extruded engraved acrylic detail plate. This identifies the knife, the blade, sheath, accessory materials, and the tested hardness of the blade. On the reverse is engraved my complete contact information with telephone numbers, email, and website address. This 2.75" x 4.25" plastic plate will last as long as the knife, and will verify the exact model design and materials indefinitely. It will never wear out, never discolor or fade, never be unreadable in any weather or exposure, unless it's completely melted—and then you have other problems! Seriously, this is much more than a piece of paper, and assures the information lasts as long as the knife and kit.
• See more about all the features in this video of a PJLT (Pararescue Light) tactical combat and rescue knife. In the video, I describe the mounts, accessories, and interfacing wear assemblies that are included in this kit; the same as you will see in the PJLT kit in the video.
• Designed by a professional for professional use, this is a top-of-the-line, brutally tough and ultimate corrosion-resistant, wear-resistant knife: a combat counterterrorism knife , sheath, and accessory package that is simply the best made. This package is comprehensive, sturdy, dependable, and useable. NO OTHER SOURCE can supply what you see here, all finely handmade to work with your gear, your outing, your mission, and your excursion, no matter the situation and exposure. This is simply the very best counterterrorism knife and kit made today.

Thanks, S. and the CT Team!